![roland cut studio driver roland cut studio driver](https://www.loesbogers.com/digitalfabrication/images/vinylcutstudioplugin.jpg)
- #Roland cut studio driver install#
- #Roland cut studio driver driver#
- #Roland cut studio driver Pc#
- #Roland cut studio driver windows#
#Roland cut studio driver install#
Install the cable clamp in the position shown in the figure.
#Roland cut studio driver driver#
* If you select the wrong folder, you will not be able to install the driver correctly.ĭouble-click "SETUP64.EXE" (64-bit version) or "SETUP.EXE" (32-bit version) inside the folder. Open the folder for your operating system. Unzip the downloaded file and open the folder that is created.
![roland cut studio driver roland cut studio driver](https://www.rolanddg.eu/-/media/roland-emea/images/products/software/cutstudio/cutstudiomobile.jpg)
#Roland cut studio driver windows#
Log on to Windows as an administrator (or as the computer's administrator). Install the driver and connect the computer and the cutting machine Press MENU to return to the original screen.ĥ. Repeat step 3 and step 4 to set "GATEWAY ADDR." (to 255.255.255.255).įor the value to enter for the gateway address, consult your network administrator. Set the gateway address of the cutting machine. If you have to set the gateway address, proceed to the next step.Ĥ. Install the driver and connect the computer and the cutting machine." Press MENU to return to the original screen, and then proceed to "5. If you are using one computer and one machine, this completes the settings on the cutting machine. Set the subnet mask to the same value used by the computer. Press twice to display the following screen.
![roland cut studio driver roland cut studio driver](https://softsoldier.com/wp-content/uploads/2019/09/Roland-CutStudio-3.13.jpg)
Set the subnet mask of the cutting machine. When you have finished making the setting, press ENTER.ģ. Make the portion that corresponds to 192.168.000 the same as the setting on the computer. Set the IP address of the computer." or a number used for another computer or device. However, be sure to specify a number that does not duplicate the setting made in "1. "XXX" represents a number from 001 to 254. Repeat step 7 and step 8 to set IP ADDRESS (to ). Press four times to display the following screen. Press or to select "AUTO" or "NETWORK," and then press ENTER. Press once to display the following screen. Press once, and then press several times to display the following screen. Press several times to display the following screen. Press MENU on the operation panel of the cutting machine twice. Set the IP address of the cutting machine. However, be sure to specify a number that does not duplicate a number used for another computer or device.Ģ. Select Use the following IP address, enter the addresses as shown below, and then click OK. The Internet Protocol Version 4 (TCP/IPv4) Properties dialog box appears. If the Internet Protocol check box was clear, click the check box to select it. Select Internet Protocol Version 4 (TCP/IPv4), and then click Properties. If the User Account Control dialog box appears, click Continue. (On Windows 7, the Local Area Connection Properties dialog box appears.) The Ethernet Properties dialog box appears.
#Roland cut studio driver Pc#
Log on to Windows as the computer's administrator or as a member of the "Administrator" group.įrom the Start menu, click Settings, and then click Network & Internet.įrom the Start menu, click PC settings, and then click Control Panel.Ĭlick Network and Internet, and then click Network and Sharing Center.įrom the Start menu, click Control Panel.Ĭlick Local Area Connection or Wireless Network Connection. For detailed information about the settings, consult your network administrator. If the computer you're using is connected to a number of networked devices or to the Internet, incorrect settings may adversely affect the entire network. The procedure and setting values described here may not be suitable for all operating environments. The examples used in the procedure for making the settings described in this section assume you are using one computer and one machine.